Difference between revisions of "Top dead centre"
m |
m |
||
| Line 2: | Line 2: | ||
| − | In a [[ | + | In a [[reciprocating engine]], the '''dead centre''' is the position of a piston in which it is farthest from, or nearest to, the [[crankshaft]]. The former is known as '''top dead centre''' ('''TDC''') while the latter is known as '''bottom dead centre''' ('''BDC'''). |
| − | + | More generally, the dead centre is any position of a [[crank]] where the applied force is straight along its axis, meaning no turning force can be applied. Many sorts of machines are crank driven, including [[unicycle]]s, [[bicycle]]s, [[tricycle]]s, various types of [[machine press]]es, [[steam locomotive]]s, and other [[steam engines]]. Crank-driven machines rely on the energy stored in a [[flywheel]] to overcome the dead centre, or are designed, in the case of [[Engine configuration|multi-cylinder engines]], so that dead centres can never exist on all cranks at the same time. A [[steam locomotive]] is an example of the latter, the connecting rods being arranged such that the dead centre for each cylinder occurs out of phase with the other one (or two) cylinders. | |
| − | + | ==Bicycles== | |
| + | [[Bicycle]] cranks have dead centres at approximately 12 o'clock and 6 o'clock where simple pushing down of the pedal will not turn the [[chainwheel]], but the rider's leg is able to apply tangential force at the pedal to overcome it. [[Fixed gear bicycles]] (without a [[freehub]]) use the [[momentum]] of the bicycle and rider to keep the chainwheel turning even if the rider makes no attempt to pedal in a circular motion. | ||
| + | ==Internal combustion engine== | ||
| + | Top dead centre is the [[datum point]] from which engine [[timing]] measurements are made. For example, [[ignition system]] timing is normally specified as degrees '''before top dead centre''' ('''BTDC''') although a very few small and fast-burning engines require a spark just '''after top dead centre''' ('''ATDC'''), such as the [[Nissan MA engine]] with hemispherical [[combustion chamber]]s, or [[Hydrogen vehicle|hydrogen engines]]. | ||
| + | |||
| + | Top dead centre for cylinder one is often marked on the crankshaft pulley, the [[flywheel]] or [[dynamic balancer]] or both, with adjacent [[timing mark]]s showing the recommended ignition timing settings as decided during engine development. These timing marks can be used to set the ignition timing either statically by hand or dynamically using a [[timing light]], by rotating the [[distributor]] in its seat. | ||
| + | |||
| + | In a multi-cylinder engine, pistons may reach top dead centre simultaneously or at different times depending on the [[engine configuration]]. For example: | ||
* In the [[V-twin]] configuration, the two pistons reach TDC at different times, equal to the [[angular displacement]] between the cylinders. | * In the [[V-twin]] configuration, the two pistons reach TDC at different times, equal to the [[angular displacement]] between the cylinders. | ||
| + | * In the [[flat twin]] configuration, two opposing pistons reach TDC simultaneously, which is also called 0° displacement. | ||
| + | * In the [[straight-4]] configuration, the two end pistons (pistons 1 and 4) reach TDC simultaneously, as do the two centre pistons (pistons 2 and 3), but these two pairs reach TDC with an angular displacement of 180°. Similar patterns are found in almost all [[straight engine]]s with even numbers of cylinders, with the two end pistons and two middle pistons moving together (not necessarily 180° out of phase however) and the intermediate pistons moving in pairs in mirror-image around the centre of the engine. | ||
| + | * In the flatplane [[V8 engine|V8]] and many larger [[V engine]]s, the piston motion within each bank is similar to that of a straight engine, however in the [[crossplane]] V8 and all [[V10 engine|V10]] engines the motion is far more complex. | ||
| + | |||
| + | The concept of top dead centre is also extended to [[pistonless rotary engine]]s, and means the point in the cycle in which the volume of a combustion chamber is smallest. This typically occurs several times per rotor revolution; In the [[Wankel engine]] for example it occurs three times for every one revolution of the rotor. | ||
| + | |||
| + | By finding the volume of the cylinder using TDC and BDC and multiplying it by the number of cylinders you have, you will get your engine displacement. | ||
| + | |||
| + | ==Steam engine== | ||
| + | As [[steam engine]]s are commonly [[Horizontal plane|horizontal]], the relevant terms are front dead centre and back dead centre rather than "top" and "bottom". | ||
| − | + | If a single-cylinder steam engine stops in either of the dead centre positions it must be moved off the dead centre before it will re-start. In small engines this is done by turning the [[flywheel]] by hand. In large engines the flywheel is moved with a lever or "turning bar". Both operations must be done with care to avoid the operator becoming entangled in the machinery. | |
| − | + | [[Steam locomotive]]s normally have two [[Cylinder (steam locomotive)|cylinders]] with the [[Crank (mechanism)|cranks]] set at [[right angle]]s so one [[piston]] will always be off the dead centre and no starting assistance is required. | |
| − | + | ==Other machines== | |
| + | This term is also used in the realm of production equipment. A mechanical punch press employs a crankshaft similar to that found in an engine. In the punch press the crankshaft drives a ram which when it is farthest away from the platen of the press is considered to be in the position of top dead centre. | ||
| − | |||
{{Automobile configurations}} | {{Automobile configurations}} | ||
Revision as of 22:41, 18 December 2009
In a reciprocating engine, the dead centre is the position of a piston in which it is farthest from, or nearest to, the crankshaft. The former is known as top dead centre (TDC) while the latter is known as bottom dead centre (BDC).
More generally, the dead centre is any position of a crank where the applied force is straight along its axis, meaning no turning force can be applied. Many sorts of machines are crank driven, including unicycles, bicycles, tricycles, various types of machine presses, steam locomotives, and other steam engines. Crank-driven machines rely on the energy stored in a flywheel to overcome the dead centre, or are designed, in the case of multi-cylinder engines, so that dead centres can never exist on all cranks at the same time. A steam locomotive is an example of the latter, the connecting rods being arranged such that the dead centre for each cylinder occurs out of phase with the other one (or two) cylinders.
Bicycles
Bicycle cranks have dead centres at approximately 12 o'clock and 6 o'clock where simple pushing down of the pedal will not turn the chainwheel, but the rider's leg is able to apply tangential force at the pedal to overcome it. Fixed gear bicycles (without a freehub) use the momentum of the bicycle and rider to keep the chainwheel turning even if the rider makes no attempt to pedal in a circular motion.
Internal combustion engine
Top dead centre is the datum point from which engine timing measurements are made. For example, ignition system timing is normally specified as degrees before top dead centre (BTDC) although a very few small and fast-burning engines require a spark just after top dead centre (ATDC), such as the Nissan MA engine with hemispherical combustion chambers, or hydrogen engines.
Top dead centre for cylinder one is often marked on the crankshaft pulley, the flywheel or dynamic balancer or both, with adjacent timing marks showing the recommended ignition timing settings as decided during engine development. These timing marks can be used to set the ignition timing either statically by hand or dynamically using a timing light, by rotating the distributor in its seat.
In a multi-cylinder engine, pistons may reach top dead centre simultaneously or at different times depending on the engine configuration. For example:
- In the V-twin configuration, the two pistons reach TDC at different times, equal to the angular displacement between the cylinders.
- In the flat twin configuration, two opposing pistons reach TDC simultaneously, which is also called 0° displacement.
- In the straight-4 configuration, the two end pistons (pistons 1 and 4) reach TDC simultaneously, as do the two centre pistons (pistons 2 and 3), but these two pairs reach TDC with an angular displacement of 180°. Similar patterns are found in almost all straight engines with even numbers of cylinders, with the two end pistons and two middle pistons moving together (not necessarily 180° out of phase however) and the intermediate pistons moving in pairs in mirror-image around the centre of the engine.
- In the flatplane V8 and many larger V engines, the piston motion within each bank is similar to that of a straight engine, however in the crossplane V8 and all V10 engines the motion is far more complex.
The concept of top dead centre is also extended to pistonless rotary engines, and means the point in the cycle in which the volume of a combustion chamber is smallest. This typically occurs several times per rotor revolution; In the Wankel engine for example it occurs three times for every one revolution of the rotor.
By finding the volume of the cylinder using TDC and BDC and multiplying it by the number of cylinders you have, you will get your engine displacement.
Steam engine
As steam engines are commonly horizontal, the relevant terms are front dead centre and back dead centre rather than "top" and "bottom".
If a single-cylinder steam engine stops in either of the dead centre positions it must be moved off the dead centre before it will re-start. In small engines this is done by turning the flywheel by hand. In large engines the flywheel is moved with a lever or "turning bar". Both operations must be done with care to avoid the operator becoming entangled in the machinery.
Steam locomotives normally have two cylinders with the cranks set at right angles so one piston will always be off the dead centre and no starting assistance is required.
Other machines
This term is also used in the realm of production equipment. A mechanical punch press employs a crankshaft similar to that found in an engine. In the punch press the crankshaft drives a ram which when it is farthest away from the platen of the press is considered to be in the position of top dead centre.